Getting Familiar with Plumbing: A Must for Installing a Bathtub
Getting Familiar with Plumbing: A Must for Installing a Bathtub
Blog Article
We have noticed this post about How to Install a Bathtub down the page on the net and thought it made sense to talk about it with you on my blog.
Installing a tub isn't exactly brain surgery, but it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed task, it is much better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you mount a new bathtub in your bathroom if you have actually already bought a brand-new tub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and product checklist must comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines are in place between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water as well as examine all joints and new pipework for leaks and also tighten them if essential. Fill the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at the very least when as this will certainly resolve it right into its final position.
Preparing for the Installation
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack a rigid seal, causing the water to pass through the wall surface between the bathroom and also the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealer can break rather early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very curious about Installing A Bathtub and I hope you appreciated the blog posting. Make sure you take a moment to promote this article if you liked it. Thanks for taking the time to read it.
Quick solution? Call. Report this page